Expert Answers about Chevrolet Work Lights
- Recommended LED Utility Lights
- Unless you go with an incadecent or halogen light like the Optronics Utility Work Light item # TL46TS, they're all going to be pretty similar to the Optronics LED Off-Road Light Bar item # UCL23CB you referenced. This one has 15,500 lumens and is one of our most popular accessory lights. For the price you can't beat it and it comes with its own mounting hardware. If you find the light is too bright you can always add some tinting film over the lens to soften the brightness.
The LED Work...
view full answer... - Dimensions of Optronics Utility Work Light
- I would be happy to provide you with the dimensions of the # TL35FS Optronics Utility Work Light - Incandescent - Flood Beam - Rectangle - Clear Lens. The measurements you are looking for are 6-5/8" long x 4-5/16" wide x 3-13/16" deep. The light face measures 5" long x 3" tall.
I have attached a video review of the light for your reference.
view full answer... - How Many Functions Can the 7 inch Round Transit Stop and Tail Light # ST90RB Do
- This 7 inch Round Transit Stop and Tail Light # ST90RB can do stop and turn signals when used on a combined stop/turn circuit, but it cannot do taillight functions as well.
The closest thing to a 7 inch 3 function trailer light we have is the 4-3/8 inch Round Trailer Tail Light, Stud Mount, 3-Function Trailer Light # ST24RB. However, this light is only 4-3/8 inches in diameter.
view full answer... - Does the 4-Way Wiring Harness for a 2002 Nissan Frontier Work w/ LED Tail Lights?
- Yes, the T-One Vehicle Wiring Harness item # 118362 will work with LED tail lights so long as the original factory wiring is still being used. This harness is custom fit for the 2002 Nissan Frontier and plugs into your Nissan's wiring harness, which is located at the rear, near the passenger's side frame rail. So long as you have the original connector you will have no issues with the upgraded lighting.
view full answer... - Does the 4-Way Wiring Harness for a 2006 Camry Work w/ LED Trailer Lights?
- Yes, it will. The Curt T-Connector Vehicle Wiring Harness item # C55308 will work with a trailer that has LED lights. This harness is confirmed to fit a 2006 Toyota Camry. It will provide you with a 4-way connector.
I have linked an installation video below.
view full answer... - What Is the Depth of the Opti-Brite LED Work Light
- The distance from the center of the mounting stud to the back of the housing on the Opti-Brite LED Work Light part # TLL64FB is 2-1/4".
view full answer... - Will Gustafson RV LED Pendant Light Work on with 12v Power?
- Yes, the Gustafson RV LED Pendant Light # 277-000422 is an LED Light designed to work on the 12v power supplied by your RV battery. This 5" diameter light is going to provide a bright, focused light perfect for your kitchen or over a dining table. When installing it, you'll need to keep the old hardware from the light you're removing, since this light does not come with any mounting screws.
view full answer... - What Does it Mean when a Trailer Light is Listed as Waterproof or Submersible
- When it comes to trailer taillights the terms waterproof and submersible are somewhat interchangeable. If a taillight is considered submersible that means that the internal circuits are waterproof and would be protected for if you were to back the trailer into water like when launching a boat.
The part # TLL56RK that you referenced is listed as waterproof and submersible so it would work great on a boat trailer.
Lights that aren't waterproof or submersible will still work just fine on...
view full answer... - Size of Lippert Replacement LED Light Strip # LC423331
- I went out to our warehouse to take a look at the Replacement LED Light Strip # LC423331 that you referenced. The light strip itself is extremely thin so it's going to pretty much fit inside any housing that's designed for this purpose. I also grabbed the complete light kit, part # LC674283, that this is a replacement strip for and found that the housing opening was just about 1/16 of an inch.
So as long as your existing housing is at least this size the replacement strip will work perfectly....
view full answer... - Would the Uni-Lite LED Mini Utility Light # UCL11CKB Work to Illuminate Running Boards
- The Uni-Lite LED Mini Utility Light # UCL11CKB is pretty bright. We had a customer leave a review telling us how surprised he was on how bright they are for only having two diodes. I think they would work well for illuminating running boards on a truck. I do think that maybe two per board would work better than one. But that depends on the length of the board.
I attached a review video for these lights that shows about how bright they would be.
view full answer... - How Long Is The Wiring On The Blazer LED Cube Light Kit # BL28VR And How Many Will Work Together?
- Yes, the Blazer LED Cube Light Kit # BL28VR can be used on your 30 amp RV as long as you have a 12 volt wiring system which this light uses. As far as how many of these lights you can hook up each remote is capable of controlling up to 4 of these lights. So the real answer is how many remotes you would use and how much 12 volt power you can afford to use. As each light draws 1.1amps of power or 20 watts per light you will want to determine how much power your converter is putting out or...
view full answer... - What Are the Mounting Dimensions on the Low Profile LED Flood Light
- There really isn't going to be a "typical" size for an oval exterior light, but if your light is overall 4.33" long and has 3.75" between the mounting holes then this light will work for you.
view full answer... - Is the Optronis License Plate Light Bracket Flat
- The Optronics License Plate Light Bracket # BK31BB is a flat bracket. This bracket is designed to work with either the Optronices Mini Trailer License Plate Light # LP31CB or the LED version # LPL31CB
view full answer... - Off-Road Lights With 10 Foot Harness for 2016 Chevy Silverado 1500
- I do have an solution for you to use off-road lights on your 2016 Chevy Silverado 500, however when I contacted Aries they were unable to tell me the length of the harness that comes with the Aries LED Work Lights # AA1501250 and there are none currently available to me that I would be able to go and measure.
There are a pair of outstanding alternatives, the Vision X Optimus Single Prime Pod Light Kit # XIL-OP110KIT which have a narrow 10-degree spot beam, or the Vision X Optimus Single...
view full answer... - Work Flood Light Fitment for 3-1/2" Wide x 2-1/4" High Spacing
- We do have some options similar to the Optronics Halogen Utility Light # QH16CTS but a little smaller:
- Vision X Utility Market Floodlight # XIL-UF32 (456 lumens and measuring 3-1/2" long x 1-7/8" tall x 7/8" deep)
- SteelHead LED Work Light # TN49RR (750 lumens and measuring 3" long x 2" wide x 2" deep)
These have plastic lens but they do fit the criteria you're looking for when it comes to size. The Vision X looks a little more clean while the SteelHead has more of a classic, "off-road"...
view full answer... - Can 14 Gauge Wire Power LED Flood Lights on Trailer
- Since LED lights like the Low Profile LED Flood Light part # 3371492135 that you referenced draw such a low amount of amperage 14 gauge wire would work fine.
view full answer... - Will the Peterson Lens Replacement Work With Premier Brand Square Trailer Lights
- I went out to the warehouse and measured the Peterson Replacement Lens, item # 440-15R, and the bolt hole pattern is 3-3/4 inches square, so it should work nicely as a replacement for your Premier brand trailer lights with 3-3/4 inch bolt pattern.
At the right I have posted a photo with the measurements for you to see.
view full answer... - Is the Optronics Trailer Light # ST45RB 12 or 24 Volt
- The Sealed, 4 inch Round Trailer Stop, Turn and Tail Light, part # ST45RB is designed to work with a 12 V system. I have attached a product review video for this light you can check out.
This light accepts the 3-prong connector like part # A45PB. The grommet used with this light is part # A45GB and is sold separately.
For a 4 inch light that is designed for a 24 volt system I recommend part # STL23R24B.
view full answer... - How to Tow a 2010 Toyota Venza
- I am sorry but I checked with all of our vendors and no one has any parts listed for flat towing a 2010 Venza. The Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit item # RM-15267 is pretty universal so it should work but I can't confirm.
I wanted to add that I pulled up the owners manual of your 2010 Toyota Venza and your vehicle is not recommended for flat towing. It says to use a tow dolly like the Demco Kar Kaddy item # DM9713045 to tow it behind your RV. This dolly also includes...
view full answer... - Warranty and Candela of the Trailer Tail Light # STL70RB
- I checked with Optronics and the Trailer Tail Light # STL70RB has a limited lifetime warranty that would cover manufacturer defects such as LEDs that stop working.
This light is rated in candela. My contact at Optronics said that it has a candela output of 14 cd for the tail lights and 201 cd on the stop and turn lights. I attached a review video for more info for you to check out as well.
view full answer...
Go To Results